1. AutomationDesk / ControlDesk / ConfigurationDesk / ECU-Test (advanced)

2. dSPACE simulator setup and maintain (advanced)

3. Test process improvement and test automation (advanced)

4. Matlab / Simulink / Stateflow (advanced)

5. LabVIEW / PXI (advanced)

6. Python / VB Scrip / C language (advanced)

7. Experience in FPGA programming on Simulink (basic)

8. CANoe / CANalyzer / PeakCAN Explorer (advanced)

9. UDS on CAN (basic)

10.E-powertrain test on test bench (advanced)

20/04/2018–01/02/2020 HiL Test Engineer | E-Powertrain Center

Guangzhou Xiaopeng Motors Technology Co., Ltd

No. 8 Songgang Road, Changxing Street, 510640 Guangzhou (China)

https://en.xiaopeng.com/

Responsibility:

1.HiL test bench setup and maintain on dSPACE SCALEXIO

2. Motor controller open loop/close loop debug on HiL simulator

3. Check test cases, Automation testcases implementation and execution

4. Documentation of the test results

5. E-powertrain test on test bench, safty operation of test bench

6. Develop a panel to simulate as a VCU and a monitor of motor controller on PeakCAN

7. Develop a APP on Visual-studio to to unlock security level1 and rewrite resolver angle offset in

motor controller according to Diagnostic Services on CAN

Activities :

1. A Delphi Motor Controller HiL/Testbench Testing. | 2018 - 2020

2. A Inovance Motor Controller HiL/Testbench Testing. | 2019 - 2020

3. A JJE Motor Controller HiL/Testbench Testing. | 2018 -2019

03/07/2017–20/04/2018 Test and Develop Engineer | E-Drive Center

Dongguan Institute, Sun Yat-sen University

NO.1Headquarters, Songshan Lake, Dongguan, 523808 Dongguan (China)

https://dgyjy.sysu.edu.cn/

responsibilities:

1.E-powertrain test on test bench

2.HiL simulation of all drive electric vehicle on PXI and CarSim

3. Rapid prototype development of motor controller on ds1103

01/09/2015–01/07/2017 Master Study in Vehicle Engineering EQF level 6

South China Agricultural University, Guangzhou (China)

General

-General English

-Experimental design and statistical analysis

-Intellectual property

Professional

-Automotive English

-Theoretical basis of mechanical control

-Computer technology

-Measurement and control technology

-Literature review and discussion of vehicle engineering

-Automotive fault diagnosis technology

Thesis

-Explerment and HiL simulation about motor controller

01/09/2010–01/07/2014 Bachelor study in Vehicle Engineering EQF level 5

Xi’an University of Science and Technology, Xi’an (China)

General

-College English / Mathematics / Linear algebra / Probability theory

-Physics / Theoretical mechanics / Material mechanics / Fluid mechanics

Professional

-Mechanical drawing / Mechanical principle / Mechanical Design

-Analog electronics / Digital electronics

-Microcomputer principle and interface technology / Micro processor

-Matlab / C language / Visual Basic

-Automotive Electrical and Electronic / Automotive testing / Vehicle vibration / Vehicle construction /

Internal combustion engine / Vehicle theory / Automotive design / Automotive manufacturing / Vehicle

English

Thesis

- Finite Element Analysis of Commercial Vehicle Frame

1. AutomationDesk / ControlDesk / ConfigurationDesk / ECU-Test (advanced)

2. dSPACE simulator setup and maintain (advanced)

3. Test process improvement and test automation (advanced)

4. Matlab / Simulink / Stateflow (advanced)

5. LabVIEW / PXI (advanced)

6. Python / VB Scrip / C language (advanced)

7. Experience in FPGA programming on Simulink (basic)

8. CANoe / CANalyzer / PeakCAN Explorer (advanced)

9. UDS on CAN (basic)

10. E-powertrain test on test bench (advanced)